Omega Vehicle Security DPS3300 Manuel d'utilisateur

http://www.omega.com e-mail: [email protected] DPS3300 Serieswall mount Multi-Channel Process Scanner

Page 9 Deviation Mode In deviation display mode, DPS3300 Series will show the differential between a pre-programmed setpoint and process variable

Page 10 To get into SETUP mode, push the SETUP key twice. The first push displays elapsed time and the second push brings the unit into the SE

Page 11 NOTE: To exit from any point during SETUP procedure or to save the newly made changes, simply press and hold the RESET key until the disp

Page 12 Setup For High Scale After setting a channel's decimal point position, the next parameter to be set is Hi Scale. This parameter de

Page 13 For High Scale) to set the desired TARE number. Once the desired TARE value is displayed, push SETUP key to enter that value and go to set

Page 14 When this parameter is set for "Normally Open", the relay is open when it is deactivated (readings are below LIMIT), and closes w

Page 15 Setup Examples Example #1: Use of the OFFSET Parameter Setup for a 4-20ma transducer signal corresponding to 0-500 gallons of fluid (read

Page 16 The channel numbers in Display Option #6 start with 'CH1 dIF' and go up to 'CH7 dIF' (CH4 dIF for 4 channel

Page 17 Setup For Channel Calibration After setting the Cold Junction Reference temperature, the next step is a display of channels for calibrat

Page 18 3. Adjust the gain pot of the instrument until the display reads '1100'. 4. Short channel #1's input with a wire or shorting

TABLE OF CONTENTS Page 1 SPECIFICATIONS ...

Page 19 Once the desired channel has been selected, push 'HI/LO' key. Pushing it once will show the high peak attained by the selected ch

Page 20 DPS3317 7 Channel Unit DPS3314 4 Channel Unit ENTER PASSCODE -- 3254 SYS CH SELECT CHANNELIP TYPE DISPLAY OPTION (Select one) ELAPSED T

Page 21 DPS3307 7 Channel Unit DPS3304 4 Channel UnitENTER PASSCODE -- 3254 SYS CH SELECT CHANNEL IP TYPE DISPLAY OPTION (Select one) ELAPSED T

Page 22 RATE DPS3300 series tracks the rate of process change/minute for each channel. This rate is displayed by first pushing the CH. SEL key to

Page 23 NOTE: LOOK UNDER SPECIFICATIONS FOR THE RATING ON RELAYS AND OPEN COLLECTOR OUTPUTS. UNDER NO CONDITION SHOULD THE RELAYS AND OPEN CO

Page 24 891011121365 4 3 2 1 714 POWER Power connection should be made to the three terminal connector as shown in figure 3. Also, make note tha

Page 25 DIRECT INTERFACE TO UNIVERSAL RELAY MODULE A special feature in the DPS3300 series units allows direct interfacing with Universal Relay Mo

Page 26 TROUBLE SHOOTING If the meter locks on a particular display, unplug and plug in again to unlock the display. A total reset clears the m

Page 27 MOUNTING Figure - 4. Rear View And Mounting Hole Locations 120mm 4.72” 151mm 5.94” SLOTS IN T

Page 28 WARRANTY

TABLE OF CONTENTS Page 2 Electro-Mechanical Relay Option ...

Page 29

Page 30 M4302/0306

Page 3 SPECIFICATIONS (Typical @ 25C and rated supply voltage unless otherwise specified) STANDARD INPUTS * 4-20ma 0-50ma 0-5Vdc 0-10Vd

Page 4 NOTE DPS3304 & DPS3314 are four channel units. Therefore, any reference to channel numbers with re

Page 5 DESCRIPTION DPS3300 Series instruments are multi-channel scanners that pack a number of functions into one unit. Tasks that require multip

Page 6 DISPLAYING PARAMETERS DPS3300 Series keeps track of various parameters and these may be displayed by pushing appropriate keys on the front

Page 7 DISPLAY MODES DPS3300 Series has multiple display modes and can be programmed to either scan, display the channel with the highest readi

Page 8 Scan Mode When setup for scan mode, individual channels are displayed for a programmed period of time. At the end of that time period the,