Omega-vehicle-security OM-420 Manuel d'utilisateur télécharger pdf (Page 1)

USING THE RPS-1in the OM-420

Omega Engineering Inc. 1 Stamford, CT

USING THE RPS-1, RECHARGEABLE POWER SUPPLY

IN THE OM-420

OVERVIEW:

The RPS-1 is a self-contained battery power source for use in conjunction with the OM-320/420 System

Base to power transducers requiring external power (e.g. Strain Gages, Pressure transducers, 4 to 20ma

Loop Transmitters, etc.) over a voltage range from 3.5 to 22 VDC.

The RPS-1 contains two User-configurable, rechargeable gel-cell type batteries and integral recharging

circuitry. The charging circuitry will accept AC or DC current from Photovoltaic arrays, wind generators,

utility sourced transformers/plug-in power supplies, or other current sources. The sealed batteries are

capable of operating in any orientation and over a temperature range of -10 to 60C. A slide switch allows

the User to configure the RPS-1 for 12 or 24VDC operation.

Two User-programmable Power Supply outputs are available which can source 7 different regulated

voltage levels from 3.5VDC to 22VDC. Outputs are short circuit / over-current protected.

The two Power Supplies can be independently programmed for output voltage as well as type of

operational mode. Two modes are available, Continuous ON or AUTOMATIC Operation. In AUTOMATIC

Operation, the power supply is under control of an optically isolated low voltage (5VDC, 0.5mA) control

input signal. This control INPUT interfaces directly to a OM-320/420 Digital Output line which can be

programmed to cycle the RPS-1 power supplies ON and OFF, providing transducer excitation under OM-

320/420 control during a logging session. This automatic power supply cycling technique maximizes RPS-

1 battery life. See Figure 1 for a sample Hypernet

Figure 1: RPS-1 Control Using HyperWare Warm-Up

Icon

1 2 3 4 5 6 7 8

Résumé du contenu

Page 1 - IN THE OM-420

USING THE RPS-1in the OM-420Omega Engineering Inc. 1 Stamford, CTUSING THE RPS-1, RECHARGEABLE POWER SUPPLYIN THE OM-420OVERVIEW:The RPS-1 is a sel

Page 2 - HARDWARE / USER CONTROLS:

USING THE RPS-1in the OM-420Omega Engineering Inc. 2 Stamford, CTAn integral State-of-Charge (SOC) indicator is provided which will display an appr

Page 3 - OPERATION / SET-UP

USING THE RPS-1in the OM-420Omega Engineering Inc. 3 Stamford, CTCONTROL INPUTTwo terminal connections are provided for connection of a low voltage

Page 4

USING THE RPS-1in the OM-420Omega Engineering Inc. 4 Stamford, CTThe MODE switch (bottom or eighth switch) should be set for the desired operation,

Page 5

USING THE RPS-1in the OM-420Omega Engineering Inc. 5 Stamford, CTvoltage is set to 12 VDC or higher output. For 12VDC or higher power supply OUTPU

Page 6 - MISCELLANEOUS

USING THE RPS-1in the OM-420Omega Engineering Inc. 6 Stamford, CTheld down for approximately 10 seconds to dissipate any battery surface charge and

Page 7 - TROUBLESHOOTING

USING THE RPS-1in the OM-420Omega Engineering Inc. 7 Stamford, CTBATTERY REPLACEMENTNOTE: USE CAUTION IN WORKING WITH THE GEL-CELL BATTERIES TO PRE

Page 8

USING THE RPS-1in the OM-420Omega Engineering Inc. 8 Stamford, CTPROBLEM: Batteries are fully discharged.SOLUTION: Charge the batteries.SYMPTOM: S

Commentaires sur ces manuels

Pas de commentaire

Omega-vehicle-security OM-420 Manuel d'utilisateur Page 1

Naviguer en ligne ou télécharger Manuel d'utilisateur pour Outils Omega-vehicle-security OM-420. Omega Vehicle Security OM-420 User Manual Manuel d'utilisatio

Résumé du contenu

Commentaires sur ces manuels

Omega-vehicle-security OM-420 Manuel d'utilisateur Page 1

Naviguer en ligne ou télécharger Manuel d'utilisateur pour Outils Omega-vehicle-security OM-420. Omega Vehicle Security OM-420 User Manual Manuel d'utilisatio

Résumé du contenu

Commentaires sur ces manuels

Produits connexes et manuels pour Outils Omega-vehicle-security OM-420