Omega-vehicle-security K9-6ATV2 Manuel d'utilisateur télécharger pdf (Page 2)

transmitter to operate your system for the purpose of stealing your vehicle or its

contents.

Additionally, in normal operation, every time the ignition switch is turned "on",

the LED Status Indicator will flash and pause for ten seconds, the number of flashes

between each pause being equal to the number of transmitters encoded to operate

your system. For example: two flashes and a pause indicate that only two

transmitters are coded to operate your system. In the event the system alerts you

to a recent transmitter addition, you can now immediately reprogram your

transmitters, effectively erasing any unauthorized transmitters.

Transmitter Code Jumping

: The transmitter sends a digitally coded signal

to the security system. The transmitter and security system will advance to another

code to use for the transmission. With each use, this digital signal changes. This

Code Jumping

feature prevents a thief from using a "code grabber" device to

record and play back a transmission for the purpose of disarming your vehicle

security system.

Page - 5

For the first 48 hours after any transmitter is encoded to operate the

system, every time the ignition switch is turned "on", the siren will chirp

rapidly for two seconds, and the LED Status Light will flash for 90 seconds.

Transmitter Operations

Also see pages 26 and 38-39

LED Light- Illuminates

when a button is pressed.

Large Transmitter Button-

Pressing and releasing this button will arm and disarm the security system. If the optional

doorlock interface is installed, the doors will lock upon arming, and unlock upon disarming

(however, if the system is in a triggered condition, disarming will not unlock the doors). If

you have the optional unlock driver's door feature, then upon disarming only the driver's

door will unlock, and if the large button is pressed again within 4 seconds, all of the doors

will unlock. Pressing and holding this button for 3 seconds will "Panic" the system- which

will sound the siren or horn, flash the exterior and interior lights and also lock the doors.

Page - 6

Small Right Transmitter

Button- If this button is

held for 3 seconds, the secu-

rity system will activate the

2nd channel output (typi-

cally used for trunk release).

If this button is pressed

twice, the system will arm

or disarm without audible

chirps.

K K

K -

Small Left Transmitter

Button- Pressing the small

left transmitter button for

2.5 seconds activates the 3rd

channel output, which may

be used to operate optional

devices. If an optional aux-

iliary sensor is part of the

system, pressing this button

within 4 seconds after arm-

ing the system will turn the

sensor off.

Arming The System Using The Transmitter

Arming The Security System Using The Transmitter: The security system

can always be armed from the transmitter provided the ignition key is “off” and the

system is disarmed and not in the Valet Mode. To arm the system, after you exit

the vehicle and close all of the doors, simply press and release the large transmitter

button once. Instantly the parking lights will flash once, the siren will chirp once and

the LED Status Indicator will begin to flash confirming that the system is armed.

Further, the doors will lock and the starter interrupt relay will engage to prevent any

attempt to start the vehicle. Your security system is now fully armed, and is ready

to respond if an intrusion attempt is detected.

Arming Bypass: Upon arming, if any sensing circuit is inoperable, that circuit

will be bypassed. For example, if the trunk is left open, you can still arm the system

with the transmitter. The bypassed circuit will automatically be reinstated for

protection 5 seconds after the circuit becomes operative, i.e., when the trunk is

closed. When a triggered circuit is in a bypassed state, all other operating circuits

will be protected normally.

Sensor By-Pass: Your security system provides you with the convenience of

temporarily deactivating any optional auxiliary sensor without affecting other

Page - 7

trigger circuits. To deactivate the sensor, simply press and release the small left

transmitter button within 4 seconds after pressing the large transmitter button when

arming the system. You will hear a second siren chirp confirming that the security

system has armed without the sensor protecting the vehicle. The next time you arm

the security system, the system will reset to its normal condition, and the sensor will

again be part of your protection.

Passively Arming The System

Passively Arming The Security System Using Last Door Arming: You can

also pre-select your security system to automatically arm and lock the doors when

the vehicle's last door is closed. The moment the last door closes the siren (or horn,

if used) will chirp once, the parking lights will flash once and the LED Status

Indicator will begin to flash rapidly. Thirty seconds later the siren will chirp again,

the doors will lock (provided that the Passive Lock feature has been chosen) and the

LED Status Indicator will slow to a steady flash, confirming that the security system

is fully armed. If a point of entry is reopened before the single siren chirp at 30

seconds, the passive arming process stops and will reset to start over when the point

of entry is re-closed.

Automatic Last Door Arming offers a high level of security, since you do not

have to remember to arm the security system every time you leave the vehicle.

Page - 8

1 2 3 4 5 6 7 8 9 10

Commentaires sur ces manuels

Pas de commentaire

Omega-vehicle-security K9-6ATV2 Manuel d'utilisateur Page 2

Commentaires sur ces manuels