Omega-vehicle-security K9-6ATV2 Manuel d'utilisateur télécharger pdf (Page 7)

Page - 24

The Anti-Carjacking feature automatically activates for each of the three

described conditions, provided that each has been programmed to operate. In each

of the three methods, the vehicle operator has 53 seconds to press the Valet Switch

to cancel the Anti-Carjacking feature. If not cancelled, at 53 seconds the siren will

start chirping, to remind the operator that Anti-Carjacking will engage. This will

continue for 7 seconds, during which time the Anti-Carjacking feature may still be

cancelled by pressing the Valet Switch. At 60 seconds, the Anti-Carjacking feature

fully engages, sounding the siren and flashing the parking lights. Thirty seconds

after the siren sounds and the parking lights flash, the starter interrupt will engage.

During this 30 second period, if the ignition is turned "off" the starter interrupt will

instantly engage.

Once fully activated, the Anti-Carjacking feature can only be deactivated by

turning the ignition "off", then "on" again, after which the Valet

Switch must be

pressed within 5 seconds. When the Anti-Carjacking feature is fully engaged, the

system will not respond to the transmitters, nor will it automatically reset after 60

seconds. The Anti-Carjacking operation will continue until deactivated or until the

vehicle's battery is drained.

Optional Pager Unit And Backup Battery

This security system is designed for easy compatibility with the Omega Pager

unit and also for a Backup Battery (both of which are optional additional compo-

nents). The Omega Pager will alert the user to a security system violation, and also

indicate which protected zone caused the violation. The Backup Battery option will

allow the security system to operate even if power is removed from the system's

control module or if the vehicle's battery is disconnected. The Omega dealer from

which you purchased your vehicle security system can provide more details on the

exact operations of each of these options.

Programming Transmitters

When adding or deleting transmitter codes to operate the security system,

follow this process:

1) Turn "on" the ignition.

2) Within 5 seconds of turning "on" the ignition, press the Valet Switch 5 times. The

siren will chirp, confirming that for the next 10 seconds the system is ready to

learn a transmitter code. When the first transmitter code is learned all existing

stored codes will be erased. To enter a transmitter code, simply press and release

Page - 25

the transmitter button which is desired to arm and disarm the system.

3) Repeat this procedure for each transmitter desired to operate the security system.

The system will chirp the siren once to confirm that each transmitter code was

learned. Both of the other two transmitter button's functions will automatically

be learned when the arm / disarm button is learned. If a code is not received

within a 10 second period, the learning process will automatically terminate.

Although this security system is programmed at the factory for the large center

transmitter button to arm and disarm the system, any one of the transmitter's three

buttons may be programmed to arm and disarm the security system. Upon the

system learning the arm / disarm button, the other two buttons are automatically

assigned other functions, as follows:

Arm / Disarm Trunk Release 3rd Channel

Large Center Button Small Right Button Small Left Button

Small Right Button Large Center Button Small Left Button

Small Left Button Large Center Button Small Right Button

Page - 26

Programming Features

Your

vehicle security system has 22 programmable features that allow your

system to be customized to fit your personal needs. To program these features "on"

or "off", follow this process:

1) Turn "off" the ignition.

2) Within 5 seconds of turning "off" the ignition, press the Valet Switch 5 times.

The siren will chirp, followed by a short siren burst, confirming that for the next

10 seconds the system is ready to receive a feature number.

3) Press the Valet Switch the number of times that is equal to the feature number.

Example: Press the Valet Switch six times if Feature #6 is to be changed.

4) The siren will respond by chirping the same amount as the feature number.

Example: The siren responds with six chirps.

5) Press the large transmitter button to turn the feature "on". When done, the siren

will respond with one chirp.

Page - 27

1 2 3 4 5 6 7 8 9 10

Commentaires sur ces manuels

Pas de commentaire

Omega-vehicle-security K9-6ATV2 Manuel d'utilisateur Page 7

Commentaires sur ces manuels